---
title: "Cross-Sections"
book: "University Earth and Space Sciences — Year 1"
subject: earth
language: en
chapter: 5
exercises: 12
source: https://one-course.com/books/earth/3/en/chapter/5-cross-sections
license: CC-BY-NC-SA-4.0
credit: "One Earth and Space Sciences Book, One Course (one-course.com)"
---

# Chapter 5 — Cross-Sections

An engineering company plans a tunnel under the Varden Hills, straight from west to east at a constant elevation of $200\,\mathrm{m}$. Before a single metre is bored, the geologists must say which rocks the machine will cut, where it will cross the fault, and how long it will spend in the limestone, a rock that may hold open cavities and water. Nobody can see inside the hills; but the [geological map](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-geological-map) of [Chapter 4](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#ch-b1-geological-maps), a few boreholes and the geometry of planes are enough to draw a vertical slice through the ground — a cross-section — and to read the answers from it. This chapter teaches how a section is built from a map, how [dips](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-attitude) and thicknesses change when a slice is cut obliquely, how boreholes are correlated, and how a section tells the history of the rocks it cuts. It ends with the tunnel.

**You already know.**

The [attitude](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-attitude) of a plane is given by its [dip direction](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-attitude) $\alpha$ and its [dip](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-attitude) $\delta$, and the plane through a point of elevation $z_0$ at the origin is $z = z_0 - \tan\delta\,(x\sin\alpha + y\cos\alpha)$; three points of a contact fix its [attitude](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-attitude); the V-rule reads the [dip](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-attitude) from the [outcrop](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-geological-map) pattern in valleys ([Chapter 4](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#ch-b1-geological-maps)). A contour line joins points of equal elevation on a topographic map (Book 1, grade 9). Younger rocks lie on older ones, and whatever cuts a rock is younger than it (Book 1, grade 7).

## 5.1 From the map to the section

**Definition 5.1 (Geological cross-section, topographic profile, vertical exaggeration).**

A *geological cross-section* is a drawing of the rock units and structures in a vertical plane through the ground, along a line drawn on the map. Its upper edge is the *topographic profile*, the curve of ground elevation along the line. The *vertical exaggeration* $e$ of a section is the ratio of its vertical scale to its horizontal scale; a section is *true to scale* when $e = 1$.

**Method 5.2 (Constructing a cross-section from a map).**

1. Draw the line of section on the map and lay the edge of a strip of paper along it; mark where each contour line crosses it, with its elevation, and where each contact and fault crosses it.
2. Draw a horizontal base line of the same length and a vertical scale of elevation (choose $e$ , and write it on the section).
3. Transfer each contour mark to its elevation and join the points smoothly: this is the [topographic profile](#def-b1-cross-sections-section) .
4. Transfer each contact and fault to the profile, at the point where it crosses the line.
5. From each such point, draw the contact into the ground with its [dip](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-attitude) *in the plane of the section* — its [apparent dip](#def-b1-cross-sections-apparent-dip) ( [Section 5.2](#sec-5-2) ) — exaggerated by $e$ if $e \ne 1$ ; use boreholes and [structure contours](#def-b1-cross-sections-structure-contour) where there are any.
6. Complete the units between the [contacts](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-geological-map) , respecting the order of superposition and the cuts, and add the legend, the scales, the orientation of the line and $e$ .

![Building a section (schematic): the crossings of the contour lines with the line X–Y are carried down to their elevations to give the topographic profile; a contact crossing the line is carried down to the profile and drawn into the ground with its apparent dip.](https://one-course.com/images/onecourse/chapters/earth-3/b1-cross-sections/fig-b7104e1c0eb7.svg)

*Building a section (schematic): the crossings of the contour lines with the line X–Y are carried down to their elevations to give the [topographic profile](#def-b1-cross-sections-section); a contact crossing the line is carried down to the profile and drawn into the ground with its [apparent dip](#def-b1-cross-sections-apparent-dip).*

The section below was built by computer from the model of the Varden Hills along the line C–D, which runs due east across the map at $y = 6\,\mathrm{km}$. It shows the [anticline](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-fold) whose core of sandstone and basement appears at $x \approx 3.5\,\mathrm{km}$, the limestone and shale on its limbs, the chalk in the [syncline](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-fold) to the east, and the normal fault. The tunnel line, at $200\,\mathrm{m}$, and the boreholes B1, B2, B3 of [Section 5.4](#sec-5-4) are drawn on it.

![Section C–D across the Varden Hills, from the model of the region. Top: vertical exaggeration e = 3; bottom: the same section true to scale (e = 1), where the 12 limbs look as gentle as they are. Colours as in the geological map of ; the fault (thick line) is the normal fault, its eastern block downthrown. The red line is the tunnel of the problem; B1–B3 are boreholes.](https://one-course.com/images/onecourse/chapters/earth-3/b1-cross-sections/fig-f2cf0d1d3b14.svg)

![Section C–D across the Varden Hills, from the model of the region. Top: vertical exaggeration e = 3; bottom: the same section true to scale (e = 1), where the 12 limbs look as gentle as they are. Colours as in the geological map of ; the fault (thick line) is the normal fault, its eastern block downthrown. The red line is the tunnel of the problem; B1–B3 are boreholes.](https://one-course.com/images/onecourse/chapters/earth-3/b1-cross-sections/fig-fe482a8f62fd.svg)

*Section C–D across the Varden Hills, from the model of the region. Top: [vertical exaggeration](#def-b1-cross-sections-section) $e = 3$; bottom: the same section true to scale ($e = 1$), where the $12{}^{\circ}$ limbs look as gentle as they are. Colours as in the [geological map](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-geological-map) of [Chapter 4](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#ch-b1-geological-maps); the fault (thick line) is the normal fault, its eastern block downthrown. The red line is the tunnel of the problem; B1–B3 are boreholes.*

[Vertical exaggeration](#def-b1-cross-sections-section) makes thin units and gentle relief readable, but it distorts every angle: the $12{}^{\circ}$ limbs of the [fold](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-fold) appear at about $32{}^{\circ}$ in the upper section. The next section says exactly how.

## 5.2 Apparent dip

**Definition 5.3 (Apparent dip).**

The *apparent dip* $\beta$ of a plane in a given vertical section is the angle between the horizontal and the trace of the plane in that section. It equals the true [dip](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-attitude) $\delta$ when the section runs along the [dip direction](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-attitude), and is zero when it runs along the [strike](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-attitude).

**Theorem 5.4 (Apparent dip).**

A plane of [dip](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-attitude) $\delta$ and [dip direction](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-attitude) $\alpha$, cut by a vertical section of [azimuth](https://one-course.com/books/earth/3/en/chapter/1-spherical-astronomy#def-b1-spherical-astronomy-horizontal) $\theta$, shows the [apparent dip](#def-b1-cross-sections-apparent-dip) $\beta$ with

$$
\tan\beta = \tan\delta\,\cos\gamma, \qquad \gamma = \alpha - \theta ,
$$

the plane going down in the direction $\theta$ when $\cos\gamma > 0$. In particular $|\beta| \le \delta$, with equality only along the [dip direction](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-attitude).

**Proof.** Take the plane $z = z_0 - \tan\delta\,(x\sin\alpha + y\cos\alpha)$ of [Chapter 4](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#ch-b1-geological-maps). Along the section, a horizontal step of length $s$ in the direction $\theta$ is $(x, y) = s(\sin\theta, \cos\theta)$, so $z = z_0 - s\tan\delta\,(\sin\theta\sin\alpha + \cos\theta\cos\alpha) =
z_0 - s\tan\delta\cos(\alpha - \theta)$. The trace is a straight line that descends by $\tan\delta\cos\gamma$ per unit horizontal distance: that is $\tan\beta$. Since $|\cos\gamma| \le 1$, $|\tan\beta| \le \tan\delta$. ∎

![Apparent dip (schematic block). A plane dipping east (blue) shows its true dip on the front face, a vertical face cut along the dip direction; on the grey vertical section, cut obliquely, its trace (red) descends more gently, with the apparent dip ; on a section along the strike, north–south, it would be horizontal.](https://one-course.com/images/onecourse/chapters/earth-3/b1-cross-sections/fig-af1d0c96659b.svg)

*[Apparent dip](#def-b1-cross-sections-apparent-dip) (schematic block). A plane dipping east (blue) shows its true [dip](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-attitude) $\delta$ on the front face, a vertical face cut along the [dip direction](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-attitude); on the grey vertical section, cut obliquely, its trace (red) descends more gently, with the [apparent dip](#def-b1-cross-sections-apparent-dip) $\beta$; on a section along the [strike](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-attitude), north–south, it would be horizontal.*

**Proposition 5.5 (Angles in an exaggerated section).**

In a section drawn with [vertical exaggeration](#def-b1-cross-sections-section) $e$, a line of [apparent dip](#def-b1-cross-sections-apparent-dip) $\beta$ is drawn at the angle $\beta'$ with $\tan\beta' = e\tan\beta$.

**Proof.** Over a horizontal distance $s$ the line drops by $s\tan\beta$; drawn with vertical scale $e$ times the horizontal scale, the drop appears as $es\tan\beta$ over the same drawn length $s$. ∎

**Example 5.6.**

The east limb of the Varden [anticline](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-fold) [dips](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-attitude) $12.16{}^{\circ}$ toward $080.7{}^{\circ}$ ([Chapter 4](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#ch-b1-geological-maps)). In the east–west section C–D, $\gamma = 80.7{}^{\circ} - 90{}^{\circ} = -9.3{}^{\circ}$, and $\tan\beta =
\tan12.16{}^{\circ}\cos9.3{}^{\circ} = 0.2154\times0.9868 = 0.2126$: $\beta =
12.0{}^{\circ}$. Drawn with $e = 3$, it appears at $\arctan(3\times0.2126) =
32.5{}^{\circ}$. In the section A–B of [azimuth](https://one-course.com/books/earth/3/en/chapter/1-spherical-astronomy#def-b1-spherical-astronomy-horizontal) $071.6{}^{\circ}$, $\gamma = 9.1{}^{\circ}$ and $\beta = 12.0{}^{\circ}$ as well: both sections run close to the [dip direction](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-attitude). The fault, which [dips](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-attitude) $60{}^{\circ}$ toward $120{}^{\circ}$, has in C–D the [apparent dip](#def-b1-cross-sections-apparent-dip) $\arctan(\tan60{}^{\circ}\cos30{}^{\circ}) = \arctan 1.5 = 56.3{}^{\circ}$.

## 5.3 Thickness

**Definition 5.7 (True thickness, vertical thickness).**

The *true thickness* $t$ of a layer is the distance between its base and its top measured perpendicular to the bedding. Its *vertical thickness* $h$ is the same distance measured along the vertical, as a vertical borehole meets it.

**Proposition 5.8 (Thickness of a dipping layer).**

For a layer of [dip](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-attitude) $\delta$:

1. $t = h\cos\delta$ ;
2. on horizontal ground, if the [outcrop](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-geological-map) of the layer has the width $w$ measured perpendicular to the [strike](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-attitude) , $t = w\sin\delta$ ;
3. on ground sloping at the angle $\sigma$ in the direction perpendicular to the [strike](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-attitude) , with $w$ measured along the ground, $t = w\sin(\delta + \sigma)$ if the ground slopes the opposite way to the [dip](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-attitude) , and $t = w\sin(\delta - \sigma)$ if it slopes the same way less steeply than the beds.

**Proof.** In the vertical plane perpendicular to the [strike](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-attitude), the base and the top of the layer are two parallel lines inclined at $\delta$, a distance $t$ apart. (1) A vertical segment joining them makes the angle $\delta$ with their common normal, so $t = h\cos\delta$. (2)–(3) A segment of length $w$ joining them along the ground makes with the bedding the angle $\delta$ when the ground is flat, $\delta + \sigma$ when the ground rises toward the [dip direction](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-attitude)’s opposite (the two inclinations add), and $\delta - \sigma$ when it falls the same way; the distance between the parallel lines is the length of the segment times the sine of that angle. ∎

![Thicknesses of a dipping layer in the vertical plane perpendicular to the strike: the true thickness t, perpendicular to the bedding; the vertical thickness h = t/; the outcrop width w = t/ on flat ground (schematic, with = 25).](https://one-course.com/images/onecourse/chapters/earth-3/b1-cross-sections/fig-a42e333b30a2.svg)

*Thicknesses of a dipping layer in the vertical plane perpendicular to the [strike](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-attitude): the [true thickness](#def-b1-cross-sections-thickness) $t$, perpendicular to the bedding; the [vertical thickness](#def-b1-cross-sections-thickness) $h = t/\cos\delta$; the [outcrop](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-geological-map) width $w = t/\sin\delta$ on flat ground (schematic, with $\delta = 25{}^{\circ}$).*

In the Varden Hills, a borehole that enters the limestone from above crosses it over $180\,\mathrm{m}$ of core: that is its [vertical thickness](#def-b1-cross-sections-thickness). Its [true thickness](#def-b1-cross-sections-thickness) is $180\cos12.16{}^{\circ} = 176.0\,\mathrm{m}$. A thin unit and a thick unit can show the same [outcrop](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-geological-map) width if their [dips](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-attitude) differ, and a steep layer can show a wide [outcrop](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-geological-map) on a slope that runs with it: thickness is never read off a map directly.

## 5.4 Boreholes and structure contours

**Definition 5.9 (Borehole log, correlation).**

A *borehole log* is the record, against depth, of the rocks met by a borehole: the units, the depths of their [contacts](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-geological-map), and any measured property. *Correlation* is the matching of the same units and [contacts](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-geological-map) from one log to another.

Three boreholes drilled on the line C–D give the following depths below the ground of the base of each unit (a dash: the contact lies above the ground, eroded):

| borehole | $x$ (km) | ground (m) | chalk | shale | limestone | sandstone |
| --- | --- | --- | --- | --- | --- | --- |
| B1 | 1.5 | 524.02 | 388.98 | 488.98 | 668.98 | 788.98 |
| B2 | 3.5 | 380.64 | — | — | 100.48 | 220.48 |
| B3 | 5.5 | 529.98 | 394.93 | 494.93 | 674.93 | 794.93 |

B2 starts in the limestone, on the crest of the [anticline](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-fold); B1 and B3 start in the chalk, on its limbs. Subtracting depths from the ground elevation gives the elevations of the [contacts](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-geological-map): the base of the limestone lies at $380.64 - 100.48 = 280.16\,\mathrm{m}$ in B2 and at $529.98 - 674.93 =
-144.95\,\mathrm{m}$ in B3, $425.11\,\mathrm{m}$ lower over $2\,\mathrm{km}$, a slope of $0.2126$: the [apparent dip](#def-b1-cross-sections-apparent-dip) of $12.0{}^{\circ}$ found above. B1 and B3 give the same thicknesses, $100\,\mathrm{m}$ of shale, $180\,\mathrm{m}$ of limestone and $120\,\mathrm{m}$ of sandstone: the units have the same [vertical thickness](#def-b1-cross-sections-thickness) on both limbs.

![The logs of boreholes B1, B2 and B3 on the line C–D, hung at their true elevations (not to horizontal scale), and their correlation: the base of the limestone (red) and of the sandstone (blue) rise from both limbs to the crest of the anticline at B2.](https://one-course.com/images/onecourse/chapters/earth-3/b1-cross-sections/fig-d2718af3e688.svg)

*The logs of boreholes B1, B2 and B3 on the line C–D, hung at their true elevations (not to horizontal scale), and their correlation: the base of the limestone (red) and of the sandstone (blue) rise from both limbs to the crest of the [anticline](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-fold) at B2.*

Where there are many boreholes, the shape of a buried contact is mapped with [structure contours](#def-b1-cross-sections-structure-contour).

**Definition 5.10 (Structure contour, structure-contour map).**

A *structure contour* of a geological surface is a line joining points of the surface at the same elevation. A *structure-contour map* draws the structure contours of one surface at a regular interval, whether the surface lies underground or has been eroded away.

For a plane, the [structure contours](#def-b1-cross-sections-structure-contour) are straight, parallel to the [strike](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-attitude), and equally spaced: an interval $\Delta z$ between contours corresponds to the horizontal spacing $\Delta z/\tan\delta$. Where a surface [folds](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-fold), its contours bend round the [fold](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-fold); where a fault cuts it, they stop and resume offset, with a gap or an overlap.

**Method 5.11 (Drawing a structure-contour map).**

1. For each borehole, and each point where the surface crops out, compute the elevation of the surface (ground elevation minus depth; at an [outcrop](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-geological-map) , the ground elevation itself).
2. Where the surface is close to a plane, take three points and find its [attitude](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-attitude) by the three-point method of [Chapter 4](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#ch-b1-geological-maps) ; draw contours parallel to the [strike](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-attitude) , spaced $\Delta z/\tan\delta$ apart.
3. Where it is not, interpolate linearly between neighbouring points (triangles of points), and join equal elevations.
4. Draw the faults first, and contour each fault block separately.

![Structure contours of the base of the limestone of the Varden Hills, every 100\, m (red, labelled every 200\, m), over the topographic contours (grey). On the limbs they run nearly north–south, parallel to the strike; round the hinges of the plunging folds they form V-shapes; at the fault (ticks on the downthrown side) they stop on the two cutoff lines of the surface, which are separated by the heave, and resume offset in the hanging wall. Section C–D is dashed.](https://one-course.com/images/onecourse/chapters/earth-3/b1-cross-sections/fig-415efe59e35d.svg)

*[Structure contours](#def-b1-cross-sections-structure-contour) of the base of the limestone of the Varden Hills, every $100\,\mathrm{m}$ (red, labelled every $200\,\mathrm{m}$), over the topographic contours (grey). On the limbs they run nearly north–south, parallel to the [strike](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-attitude); round the hinges of the plunging [folds](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-fold) they form V-shapes; at the fault (ticks on the downthrown side) they stop on the two cutoff lines of the surface, which are separated by the [heave](#def-b1-cross-sections-throw), and resume offset in the hanging wall. Section C–D is dashed.*

## 5.5 From the section to the history

A section shows not only where the rocks are but how they came to be there. The [contacts](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-geological-map) between units record continuous deposition, or a gap.

**Definition 5.12 (Unconformity, angular unconformity, disconformity).**

An *unconformity* is a surface of erosion or non-deposition that separates younger rocks from older ones, and so marks a gap in the record. In an *angular unconformity* the older beds were tilted or folded before the younger ones were laid across their eroded edges, so the two sets of beds meet at an angle. In a *disconformity* the beds above and below are parallel, and the gap shows only as an erosion surface or as missing fossils or ages.

**Definition 5.13 (Fault throw, heave).**

The *throw* of a fault is the vertical component of the displacement of a marker surface across it; its *heave* is the horizontal component, measured in the [dip direction](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-attitude) of the fault. For a dip-slip fault of [dip](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-attitude) $\varphi$, $\text{heave} = \text{throw}/\tan\varphi$.

The normal fault of the Varden Hills [dips](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-attitude) $60{}^{\circ}$ and has a [throw](#def-b1-cross-sections-throw) of $200\,\mathrm{m}$: its [heave](#def-b1-cross-sections-throw) is $200/\tan60{}^{\circ} = 115.5\,\mathrm{m}$. In section C–D, oblique to the fault’s [dip direction](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-attitude), the fault appears at $56.3{}^{\circ}$, and the same $200\,\mathrm{m}$ of [throw](#def-b1-cross-sections-throw) separates the two cutoffs of a contact by $200/1.5 = 133.3\,\mathrm{m}$ along the section. To *restore* the section — to see the rocks as they were before the fault moved — the hanging-wall block is slid back up the fault plane by the slip; restoring the folding as well, by unbending the layers, would bring back the flat-lying cover over the eroded basement. Reading a section from the bottom up, the history of the Varden Hills follows: the schist, the granite that intrudes it, erosion, the [angular unconformity](#def-b1-cross-sections-unconformity), the cover laid flat, the folding, the faulting, and the erosion that made today’s hills.

**History — Hutton at Siccar Point.**

At Siccar Point, on the south-east coast of Scotland, near-vertical layers of grey sandstone and mudstone of early Silurian age are cut by an erosion surface and covered by gently inclined red breccia, conglomerate and sandstone of Late Devonian age. James Hutton described this [angular unconformity](#def-b1-cross-sections-unconformity) in his *Theory of the Earth*, read to the Royal Society of Edinburgh and printed in its *Transactions* in 1788, then expanded in a book in 1795, and a sketch by Sir James Hall records what Hutton saw. The lower beds had been laid down flat on a sea floor, turned up on edge, raised and worn down; only then were the upper beds deposited across them, and the whole raised again. Each step demanded a span of time far longer than anyone had imagined, and Hutton’s reading of this [outcrop](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-geological-map) is often cited as the moment geology discovered how old the Earth is.

![Hutton’s unconformity at Siccar Point: near-vertical grey Silurian beds below, gently inclined red Devonian beds above. Photograph PawełS, CC BY-SA 4.0 (Wikimedia Commons).](https://one-course.com/images/onecourse/chapters/earth-3/b1-cross-sections/img-386991539ad5.jpg)

*Hutton’s [unconformity](#def-b1-cross-sections-unconformity) at Siccar Point: near-vertical grey Silurian beds below, gently inclined red Devonian beds above. Photograph PawełS, CC BY-SA 4.0 (Wikimedia Commons).*

**In the field — Geology for a tunnel.**

![](https://one-course.com/images/onecourse/chapters/earth-3/b1-cross-sections/img-fba1e96e0423.jpg)

Before a tunnel is designed, engineering geologists build sections along its line from the [geological map](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-geological-map), from boreholes drilled at intervals along the route, and from geophysical surveys. They predict each unit the tunnel will cut, the faults it will cross, and where water may enter. During boring, the geologists of the contractor log the rock exposed at the face at every advance, compare it with the prediction, and update the section; probe holes drilled ahead of the machine test the ground before the machine reaches it, especially near a predicted fault or in limestone that may hold cavities. A fault zone of crushed rock is a classic hazard, all the more when the same rock lies on both sides and nothing in the face warns of it.

## 5.6 Exercises

**Exercise 5.1 ★.**

A section is drawn from a map at the scale 1:25 000, with a vertical scale of $1\,\mathrm{cm}$ for $100\,\mathrm{m}$. What is its [vertical exaggeration](#def-b1-cross-sections-section)?

**Solution of Exercise 5.1.**

At 1:25 000, $1\,\mathrm{cm}$ on the map is $250\,\mathrm{m}$ on the ground. The vertical scale is $1\,\mathrm{cm}$ for $100\,\mathrm{m}$, so the vertical scale is $250/100 = 2.5$ times the horizontal one: $e = 2.5$.

**Exercise 5.2 ★.**

A bed [dips](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-attitude) $40{}^{\circ}$ toward $090{}^{\circ}$. What is its [apparent dip](#def-b1-cross-sections-apparent-dip) in a vertical section of [azimuth](https://one-course.com/books/earth/3/en/chapter/1-spherical-astronomy#def-b1-spherical-astronomy-horizontal) $060{}^{\circ}$? Of [azimuth](https://one-course.com/books/earth/3/en/chapter/1-spherical-astronomy#def-b1-spherical-astronomy-horizontal) $000{}^{\circ}$?

**Solution of Exercise 5.2.**

$\gamma = 90{}^{\circ} - 60{}^{\circ} = 30{}^{\circ}$, and $\tan\beta = \tan40{}^{\circ}
\cos30{}^{\circ} = 0.8391\times0.8660 = 0.7267$: $\beta = 36.0{}^{\circ}$, the bed going down toward the east end of the section. In the section of [azimuth](https://one-course.com/books/earth/3/en/chapter/1-spherical-astronomy#def-b1-spherical-astronomy-horizontal) $000{}^{\circ}$, $\gamma = 90{}^{\circ}$ and $\beta = 0$: the section runs along the [strike](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-attitude) and the bed appears horizontal.

**Exercise 5.3 ★.**

A vertical borehole crosses $120\,\mathrm{m}$ of sandstone whose beds [dip](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-attitude) $12.16{}^{\circ}$. What is the [true thickness](#def-b1-cross-sections-thickness) of the sandstone?

**Solution of Exercise 5.3.**

$t = h\cos\delta = 120\times\cos12.16{}^{\circ} = 120\times0.9776 =
117.3\,\mathrm{m}$.

**Exercise 5.4 ★.**

A contact dipping $12{}^{\circ}$ in the plane of a section is drawn with [vertical exaggerations](#def-b1-cross-sections-section) of 2, 3 and 5. At what angles does it appear?

**Solution of Exercise 5.4.**

$\tan12{}^{\circ} = 0.2126$. With $e = 2$: $\arctan 0.4251 = 23.0{}^{\circ}$; with $e = 3$: $\arctan 0.6377 = 32.5{}^{\circ}$; with $e = 5$: $\arctan 1.0628 =
46.7{}^{\circ}$. The angle grows much less than $e$ itself, and never reaches $90{}^{\circ}$.

**Exercise 5.5 ★★.**

A layer [dips](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-attitude) $25{}^{\circ}$. Its [outcrop](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-geological-map) is $300\,\mathrm{m}$ wide, measured perpendicular to the [strike](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-attitude). Compute its [true thickness](#def-b1-cross-sections-thickness) (a) on flat ground; (b) on ground sloping at $10{}^{\circ}$ the opposite way to the [dip](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-attitude), the width being measured along the ground; (c) on ground sloping at $10{}^{\circ}$ the same way as the [dip](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-attitude).

**Solution of Exercise 5.5.**

(a) $t = 300\sin25{}^{\circ} = 126.8\,\mathrm{m}$. (b) $t = 300\sin35{}^{\circ} =
172.1\,\mathrm{m}$. (c) $t = 300\sin15{}^{\circ} = 77.6\,\mathrm{m}$. The same [outcrop](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-geological-map) width can mean thicknesses differing by more than a factor of two: the slope of the ground must always be taken into account.

**Exercise 5.6 ★★.**

A bed shows an [apparent dip](#def-b1-cross-sections-apparent-dip) of $20{}^{\circ}$ to the north in a north–south section, and of $30{}^{\circ}$ to the east in an east–west section. Find its [dip direction](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-attitude) and its true [dip](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-attitude).

**Solution of Exercise 5.6.**

With [dip direction](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-attitude) $\alpha$ and [dip](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-attitude) $\delta$, the theorem gives in the north–south section ($\theta = 0$) $\tan20{}^{\circ} = \tan\delta\cos\alpha$, and in the east–west section ($\theta = 90{}^{\circ}$) $\tan30{}^{\circ} =
\tan\delta\cos(\alpha - 90{}^{\circ}) = \tan\delta\sin\alpha$. Dividing, $\tan\alpha = 0.5774/0.3640 = 1.586$, $\alpha = 057.8{}^{\circ}$; adding the squares, $\tan\delta = \sqrt{0.3640^2 + 0.5774^2} = 0.6825$, $\delta =
34.3{}^{\circ}$. Both [apparent dips](#def-b1-cross-sections-apparent-dip) are smaller than the true [dip](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-attitude), as they must be.

**Exercise 5.7 ★★.**

The base of the limestone on the east limb [dips](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-attitude) $12.16{}^{\circ}$. What is the horizontal spacing of its [structure contours](#def-b1-cross-sections-structure-contour) drawn every $100\,\mathrm{m}$? Check it on the [structure-contour map](#def-b1-cross-sections-structure-contour).

**Solution of Exercise 5.7.**

$100/\tan12.16{}^{\circ} = 100/0.2155 = 464.1\,\mathrm{m}$. On the map, the [structure contours](#def-b1-cross-sections-structure-contour) of the east limb are indeed a little less than half a kilometre apart, equally spaced and parallel: the limb is a plane.

**Exercise 5.8 ★★.**

From the borehole table, compute the elevation of the base of the shale in B1 and B3. Above B2 the shale has been eroded: from the [vertical thickness](#def-b1-cross-sections-thickness) of the limestone, find the elevation its base would have there, and the [apparent dip](#def-b1-cross-sections-apparent-dip) of that contact between B1 and B2 in section C–D. What does the comparison of B1 and B3 tell about the [fold](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-fold)?

**Solution of Exercise 5.8.**

B1: $524.02 - 488.98 = 35.04\,\mathrm{m}$; B3: $529.98 - 494.93 =
35.05\,\mathrm{m}$. Above B2, the base of the shale is the top of the limestone, $180\,\mathrm{m}$ above its base: $280.16 + 180 = 460.16\,\mathrm{m}$, higher than the ground ($380.64\,\mathrm{m}$), which is why it is eroded there. Between B1 and B2 the contact rises by $460.16 - 35.04 = 425.12\,\mathrm{m}$ over $2000\,\mathrm{m}$: a slope of $0.2126$, an [apparent dip](#def-b1-cross-sections-apparent-dip) of $12.0{}^{\circ}$. B1 and B3, at the same distance on either side of B2, find every contact at the same elevation within $1\,\mathrm{cm}$: the [fold](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-fold) is symmetric about a vertical axial plane at $x = 3.5\,\mathrm{km}$, its two limbs dipping equally, and no fault cuts the section between them.

**Exercise 5.9 ★★.**

A normal fault dipping $50{}^{\circ}$ toward $180{}^{\circ}$ has a [throw](#def-b1-cross-sections-throw) of $150\,\mathrm{m}$. Compute its [heave](#def-b1-cross-sections-throw). In a vertical section of [azimuth](https://one-course.com/books/earth/3/en/chapter/1-spherical-astronomy#def-b1-spherical-astronomy-horizontal) $150{}^{\circ}$, what are the [apparent dip](#def-b1-cross-sections-apparent-dip) of the fault and the separation of the two cutoffs of a horizontal bed along the section?

**Solution of Exercise 5.9.**

[Heave](#def-b1-cross-sections-throw) $= 150/\tan50{}^{\circ} = 150/1.1918 = 125.9\,\mathrm{m}$. In the section of [azimuth](https://one-course.com/books/earth/3/en/chapter/1-spherical-astronomy#def-b1-spherical-astronomy-horizontal) $150{}^{\circ}$, $\gamma = 30{}^{\circ}$ and $\tan\beta = 1.1918\times0.8660 =
1.0321$: the fault appears with the [apparent dip](#def-b1-cross-sections-apparent-dip) $45.9{}^{\circ}$. The cutoffs of a horizontal bed are $150\,\mathrm{m}$ apart vertically on that trace, hence $150/1.0321 = 145.3\,\mathrm{m}$ apart along the section, more than the [heave](#def-b1-cross-sections-throw), since the section crosses the fault obliquely.

**Exercise 5.10 ★★★.**

For a bed dipping $40{}^{\circ}$, in which section directions is the [apparent dip](#def-b1-cross-sections-apparent-dip) half the true [dip](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-attitude), that is $20{}^{\circ}$? Show that the [apparent dip](#def-b1-cross-sections-apparent-dip) varies little near the [dip direction](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-attitude) and fast near the [strike](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-attitude).

**Solution of Exercise 5.10.**

$\cos\gamma = \tan20{}^{\circ}/\tan40{}^{\circ} = 0.3640/0.8391 = 0.4338$, so $\gamma = 64.3{}^{\circ}$: the sections of [azimuths](https://one-course.com/books/earth/3/en/chapter/1-spherical-astronomy#def-b1-spherical-astronomy-horizontal) $\alpha \pm 64.3{}^{\circ}$ (and the opposite directions, where the bed rises). The [apparent dip](#def-b1-cross-sections-apparent-dip) is $40.0{}^{\circ}$, $39.6{}^{\circ}$, $38.3{}^{\circ}$ and $36.0{}^{\circ}$ for $\gamma = 0$, $10{}^{\circ}$, $20{}^{\circ}$, $30{}^{\circ}$, but $22.8{}^{\circ}$, $16.0{}^{\circ}$, $8.3{}^{\circ}$ and $0$ for $\gamma = 60{}^{\circ}$, $70{}^{\circ}$, $80{}^{\circ}$, $90{}^{\circ}$. Indeed, differentiating $\tan\beta = \tan\delta\cos\gamma$, $\dfrac{\mathrm d\beta}{\mathrm d\gamma} =
-\dfrac{\tan\delta\sin\gamma}{1 + \tan^2\delta\cos^2\gamma}$, which is zero at $\gamma = 0$ and equals $-\tan\delta$ at $\gamma = 90{}^{\circ}$: a section a little off the [dip direction](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-attitude) shows nearly the true [dip](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-attitude), while near the [strike](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-attitude) every degree of [azimuth](https://one-course.com/books/earth/3/en/chapter/1-spherical-astronomy#def-b1-spherical-astronomy-horizontal) changes the [apparent dip](#def-b1-cross-sections-apparent-dip) by almost a degree.

**Exercise 5.11 ★★★.**

A borehole crosses the limestone of the east limb ([true thickness](#def-b1-cross-sections-thickness) $176.0\,\mathrm{m}$, [dip](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-attitude) $12.16{}^{\circ}$ toward $080.7{}^{\circ}$). What length of core does it recover (a) if vertical; (b) if inclined at $60{}^{\circ}$ below the horizontal toward $260.7{}^{\circ}$; (c) inclined at $60{}^{\circ}$ toward $080.7{}^{\circ}$? (Hint: the length is $t/\cos\psi$, where $\psi$ is the angle between the borehole and the normal to the bedding.)

**Solution of Exercise 5.11.**

The beds [dip](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-attitude) east, so the normal to the bedding, followed downward, is tilted $12.16{}^{\circ}$ from the vertical toward the west, toward $260.7{}^{\circ}$. (a) A vertical borehole makes the angle $\psi = 12.16{}^{\circ}$ with it: $176.0/\cos12.16{}^{\circ} = 180.0\,\mathrm{m}$, the [vertical thickness](#def-b1-cross-sections-thickness). (b) A borehole plunging $60{}^{\circ}$ toward $260.7{}^{\circ}$ is tilted $30{}^{\circ}$ from the vertical on the same side as the normal: $\psi = 30{}^{\circ} - 12.16{}^{\circ} =
17.84{}^{\circ}$, $\cos\psi = 0.9519$, and the core is $176.0/0.9519 =
184.9\,\mathrm{m}$ long. (c) Toward $080.7{}^{\circ}$ it is tilted on the other side: $\psi = 30{}^{\circ} + 12.16{}^{\circ} = 42.16{}^{\circ}$, $\cos\psi = 0.7413$, and the core is $176.0/0.7413 = 237.4\,\mathrm{m}$ long. The core is shortest, equal to $t$, when the borehole runs along the normal, plunging $77.84{}^{\circ}$ toward $260.7{}^{\circ}$.

**Exercise 5.12 ★★★.**

At an [angular unconformity](#def-b1-cross-sections-unconformity), the beds below [dip](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-attitude) $70{}^{\circ}$ toward $090{}^{\circ}$ and the beds above [dip](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-attitude) $20{}^{\circ}$ toward $270{}^{\circ}$, with the same [strike](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-attitude). Rotate the whole [outcrop](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-geological-map) about the [strike](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-attitude) to bring the upper beds back to horizontal: what was the [dip](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-attitude) of the lower beds when the upper ones were deposited? Write the history of the [outcrop](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-geological-map) in order.

**Solution of Exercise 5.12.**

In the east–west vertical plane, with the angles measured from the east, the upper beds rise toward the east at $20{}^{\circ}$ and the lower beds go down toward the east at $70{}^{\circ}$. Rotating the [outcrop](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-geological-map) about the [strike](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-attitude) by $20{}^{\circ}$, east side down, makes the upper beds horizontal and brings the lower beds to $70{}^{\circ} + 20{}^{\circ} = 90{}^{\circ}$: they were vertical when the upper beds were deposited. History, from the oldest event: the lower beds are deposited flat; they are turned up on edge, to the vertical, and raised; their edges are eroded to a surface; the upper beds are deposited across that surface; the whole is tilted by $20{}^{\circ}$ down to the west; erosion cuts today’s ground surface. It is the history of Hutton’s [outcrop](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-geological-map) at Siccar Point.

## 5.7 Problem: A tunnel under the Varden Hills

**Problem 5.1.**

Weekend problem — which rocks a tunnel will cut, where it will meet the fault, and how much limestone it will bore

The tunnel runs due east along the line C–D ($y = 6\,\mathrm{km}$) at the constant elevation of $200\,\mathrm{m}$, from $x = 1\,\mathrm{km}$ to $x =
9\,\mathrm{km}$. The ground elevation along C–D is, every kilometre from $x = 0$:

| $x$ (km) | 0 | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10 |
| --- | --- | --- | --- | --- | --- | --- | --- | --- | --- | --- | --- |
| $z$ (m) | 509 | 556 | 467 | 370 | 435 | 534 | 501 | 455 | 406 | 339 | 405 |

Use the borehole table of the chapter, the section C–D drawn with $e = 3$, the [attitude](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-attitude) of the east limb ([dip](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-attitude) $12.16{}^{\circ}$ toward $080.7{}^{\circ}$; the west limb is its mirror image, dipping toward $279.3{}^{\circ}$), and the normal fault, which [dips](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-attitude) $60{}^{\circ}$ toward $120{}^{\circ}$, has a [throw](#def-b1-cross-sections-throw) of $200\,\mathrm{m}$, and passes through the point $x = 4.30\,\mathrm{km}$, $y = 1.00\,\mathrm{km}$, $z = 250\,\mathrm{m}$.

**Part I — The profile and the units.**

1. What are the greatest and the smallest thicknesses of rock above the tunnel at the kilometre points between $x = 1$ and $x = 9$ ?
2. On the printed section, $1\,\mathrm{km}$ of horizontal distance measures $1.4\,\mathrm{cm}$ and $1\,\mathrm{km}$ of elevation measures $4.2\,\mathrm{cm}$ . Check that $e = 3$ .
3. From log B2, find the elevation of the base of the sandstone on the crest of the [anticline](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-fold) .
4. In which unit is the tunnel at $x = 3.5\,\mathrm{km}$ ?
5. Compute the elevation of the base of the limestone in B1 and B3.
6. From the section, list in order the units the tunnel crosses from $x = 1$ to $x = 9\,\mathrm{km}$ .

**Part II — Dips in the section.**

7. Compute the [apparent dip](#def-b1-cross-sections-apparent-dip) of the east limb in C–D from its [attitude](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-attitude) .
8. Check it from the elevations of the base of the limestone in B2 and B3.
9. At what angle is the east limb drawn in the section with $e = 3$ ?
10. Compute the [apparent dip](#def-b1-cross-sections-apparent-dip) of the fault in C–D.
11. Why is the [apparent dip](#def-b1-cross-sections-apparent-dip) of the limbs in C–D so close to their true [dip](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-attitude) , and that of the fault less so?

**Part III — The fault.**

12. Show that, on the plane $y = 6\,\mathrm{km}$, the fault lies at $$x = 4300 + \frac{2500 - (z - 250)\tan30{}^{\circ}}{\sin120{}^{\circ}}  \quad\text{(metres)}.$$
13. Where does the tunnel meet the fault?
14. Compute the [heave](#def-b1-cross-sections-throw) of the fault, and the separation of the cutoffs of a contact along C–D.
15. Which block is downthrown, and which unit lies at tunnel level on each side of the fault?
16. Why is the fault a hazard that the tunnelling crew could not see coming from the rock at the face? How do the engineers guard against it?

**Part IV — The limestone.**

17. What is the [vertical thickness](#def-b1-cross-sections-thickness) of the limestone in B1?
18. What is its [true thickness](#def-b1-cross-sections-thickness) ?
19. Show that, west of the fault on C–D, the base of the sandstone lies at $$z_b = 160.16 - |x - 3500|\tan12.0{}^{\circ} \quad\text{(metres)}.$$
20. The tunnel is in the limestone when its base lies below $200\,\mathrm{m}$ and its top above. Show that this happens for $377.1 < |x - 3500|  < 1224.0$ .
21. Give the four points where the tunnel enters and leaves the limestone.
22. Show that the length bored on each limb is $h/\tan\beta$ , where $h$ is the [vertical thickness](#def-b1-cross-sections-thickness) and $\beta$ the [apparent dip](#def-b1-cross-sections-apparent-dip) , and compute it.
23. What total length of limestone does the tunnel bore through?

**Solution of Problem 5.1.**

**1.** The thickness above the tunnel is $z - 200$: largest at $x = 1\,\mathrm{km}$, $556 - 200 = 356\,\mathrm{m}$; smallest at $x =
9\,\mathrm{km}$, $339 - 200 = 139\,\mathrm{m}$.

**2.** $1\,\mathrm{km}$ of elevation measures $4.2\,\mathrm{cm}$ and $1\,\mathrm{km}$ of distance $1.4\,\mathrm{cm}$: $e = 4.2/1.4 = 3$.

**3.** $380.64 - 220.48 = 160.16\,\mathrm{m}$.

**4.** In B2 the base of the limestone is at $380.64 - 100.48 =
280.16\,\mathrm{m}$ and the base of the sandstone at $160.16\,\mathrm{m}$: the tunnel, at $200\,\mathrm{m}$, is in the sandstone.

**5.** B1: $524.02 - 668.98 = -144.96\,\mathrm{m}$; B3: $529.98 - 674.93 =
-144.95\,\mathrm{m}$.

**6.** From west to east: chalk, shale, limestone, sandstone (in the core of the [anticline](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-fold)), limestone, shale, and chalk again as far as $x = 9\,\mathrm{km}$, through the [syncline](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-fold) and across the fault.

**7.** $\gamma = 80.7{}^{\circ} - 90{}^{\circ} = -9.3{}^{\circ}$; $\tan\beta =
\tan12.16{}^{\circ}\cos9.3{}^{\circ} = 0.2155\times0.9869 = 0.2126$: $\beta =
12.0{}^{\circ}$, down toward the east.

**8.** $(280.16 + 144.95)/2000 = 425.11/2000 = 0.2126$: $12.0{}^{\circ}$.

**9.** $\arctan(3\times0.2126) = \arctan 0.6377 = 32.5{}^{\circ}$.

**10.** $\gamma = 120{}^{\circ} - 90{}^{\circ} = 30{}^{\circ}$; $\tan\beta =
\tan60{}^{\circ}\cos30{}^{\circ} = 1.732\times0.866 = 1.500$: $\beta = 56.3{}^{\circ}$.

**11.** The limbs [dip](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-attitude) toward $080.7{}^{\circ}$ or $279.3{}^{\circ}$, only $9.3{}^{\circ}$ from the line of section, and $\cos9.3{}^{\circ} = 0.987$; the fault [dips](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-attitude) toward $120{}^{\circ}$, $30{}^{\circ}$ from it, and $\cos30{}^{\circ} = 0.866$.

**12.** The fault plane is $z = 250 - \tan60{}^{\circ}\,[(x - 4300)
\sin120{}^{\circ} + (y - 1000)\cos120{}^{\circ}]$. With $y = 6000$, $(y - 1000)
\cos120{}^{\circ} = -2500$, so $(x - 4300)\sin120{}^{\circ} = 2500 - (z - 250)/
\tan60{}^{\circ}$, and $1/\tan60{}^{\circ} = \tan30{}^{\circ}$.

**13.** At $z = 200$: $x = 4300 + (2500 + 50\times0.5774)/0.8660 =
4300 + 2528.9/0.8660 = 7220\,\mathrm{m}$, that is $7.22\,\mathrm{km}$ from C.

**14.** [Heave](#def-b1-cross-sections-throw) $= 200/\tan60{}^{\circ} = 115.5\,\mathrm{m}$; separation along C–D $= 200/1.500 = 133.3\,\mathrm{m}$.

**15.** The fault [dips](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-attitude) east-south-east and is normal: the hanging wall, to the east, is downthrown. At tunnel level the chalk lies on both sides of the fault: west of it, the chalk of the [syncline](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-fold); east of it, chalk brought down $200\,\mathrm{m}$.

**16.** The tunnel stays in chalk across the fault, so no change of rock at the face announces it; only a zone of crushed rock, and perhaps water, does. The engineers predict its position from the section (here $7.22\,\mathrm{km}$), drill probe holes ahead of the machine as it approaches, and prepare support for the crushed zone.

**17.** $668.98 - 488.98 = 180.00\,\mathrm{m}$.

**18.** $t = 180\cos12.16{}^{\circ} = 176.0\,\mathrm{m}$.

**19.** On the crest ($x = 3500$) the base of the sandstone is at $160.16\,\mathrm{m}$ (question 3); it goes down on both limbs with the [apparent dip](#def-b1-cross-sections-apparent-dip) $12.0{}^{\circ}$ of question 7, that is by $\tan12.0{}^{\circ}$ per metre of horizontal distance from the axis.

**20.** The base of the limestone is $120\,\mathrm{m}$ above the base of the sandstone, at $280.16 - u\tan12.0{}^{\circ}$ with $u = |x - 3500|$, and its top $180\,\mathrm{m}$ higher, at $460.16 - u\tan12.0{}^{\circ}$. With $\tan12.0{}^{\circ} =
0.21256$: the base is below $200\,\mathrm{m}$ when $u > 80.16/0.21256 = 377.1$, and the top above it when $u < 260.16/0.21256 = 1224.0$.

**21.** $x = 3500 \pm 377.1$ and $3500 \pm 1224.0$: the tunnel is in the limestone from $2276\,\mathrm{m}$ to $3123\,\mathrm{m}$ and from $3877\,\mathrm{m}$ to $4724\,\mathrm{m}$.

**22.** Along a horizontal line, the base and the top of the limestone, $180\,\mathrm{m}$ apart vertically and both sloping at $\tan\beta$, are crossed a horizontal distance $h/\tan\beta$ apart: $180/0.21256 = 846.8\,\mathrm{m}$ on each limb, the same to rounding as $1224.0 - 377.1 = 846.9$.

**23.** $2\times846.8 = 1693.7\,\mathrm{m}$: the tunnel bores through **about $1694\,\mathrm{m}$ of limestone**, more than a fifth of its $8\,\mathrm{km}$ length, in two stretches of $847\,\mathrm{m}$ on either side of the sandstone core of the [anticline](https://one-course.com/books/earth/3/en/chapter/4-geological-maps#def-b1-geological-maps-fold).